NJR2836 series (Ku-band PLL LNB - Int. Ref.)
Ku-band LNB (Single-band)
- Frequency Organization
- RF Frequency: 12.25 to 12.75 GHz
- IF Frequency: 950 to 1,450 MHz
- LO Frequency: 11.3 GHz
- Low Noise Performance
- Noise Figure(NF): 0.8 dB typ.
- LO Frequency Stability Line-up
- H-type: +/- 10 ppm (+/- 100 kHz typ.)
- S-type: +/- 3 ppm (+/- 30 kHz typ.)
- U-type: +/- 1 ppm (+/- 10 kHz typ.)
- Small Size & Light Weight
- Weight: 260 g
- Other Features
- RoHS Compliance
||12.25 to 12.75 GHz
||+/- 10 ppm
(+/- 100 kHz typ.)
||+/- 3 ppm
(+/- 30 kHz typ.)
||+/- 1 ppm
(+/- 10 kHz typ.)
Relevant Products & Accessories
|RF Input Interface
||Waveguide, WR75 (with Groove)
|IF Output Interface
||Coax. Connector, N-type Female (50 Ω)
|Coax. Connector, F-type Female (75 Ω)
|Noise Figure(NF) @ +25 ℃
||0.8 dB typ.
|Linear Gain @ +25 ℃
||60 dB typ., 55 dB min.
|Input Power Voltage Requirement
||+24 VDC (+12 to +24 VDC)
||250 mA max.
|Operating Temperature Range
||-40 to +60 ℃
|Waterproof / Dustproof (IP-code)
(w/o Interfaces & Screws)
|(L) 100.5 x (W) 40 x (H) 40 mm
- (1)While we continually strive to improve the quality and reliability of our products, failures will occur in microwave products over time. For this reason, it is important that customers fulfill their responsibilities to ensure designed-in safety – including failsafe functions, redundancy, and measures to prevent malfunctions and the spread of fire – in order to avoid injuries, accidents, or social repercussions resulting from the failure of any product related to satellite communications on this website (hereinafter, “the product”). Customers must pay careful attention to ensuring the safety of their equipment.
- (2)The product is designed and tested to function in accordance with its specifications. Do not use under conditions that deviate from the product specifications included in the delivery specifications. We assume no responsibility and shall not be liable for any injuries, accidents, or social repercussions resulting from the product being in a poor or damaged state because it was used under conditions that depart from the specifications.
- (3)The product is covered by a warranty for one year following delivery unless otherwise stipulated in the contract or delivery conditions. In the event of a failure for which we are responsible occurring during the warranty period, we undertake to repair or replace the product free of charge. Note, however, that the warranty does not cover failures such as those listed here (see bullets below), even if they occur within the warranty period. In addition, in the case of a product being repaired or replaced by us, the starting date for the warranty period is still the original delivery date of the product.
In addition, the product warranty is limited to the provision of repair services or replacement at no cost. It does not cover secondary damage (to equipment, business opportunities, profits, etc.) or any other damage that may have resulted from failure of the product.
- Failure due to the product being used in conditions other than those stipulated in the data sheet, specification sheet, etc.
- Failure due to modifications or repairs carried out by some entity other than our company
- Failure determined to be the result of unsuitable maintenance or replacement of a consumable item that requires due maintenance
- Failure due to circumstances that were unforeseeable given the scientific/technological standards at the time of shipment
- Other failures due to external factors such as fire, earthquake, flood and power supply anomalies for which we are not responsible
- (4)The product must be handled appropriately to ensure its continued reliability. Since it can be damaged by the intrusion of water, dust, oil, chemicals, etc., it must be given appropriate protection. Even in the case of a product with an airtight construction, avoid using it in an environment that exceeds the stated levels of waterproofing/dustproofing. Also, be sure to use connectors and waveguides properly.
If replacement parts such as fans are included, proper maintenance is necessary. To maintain product performance and functionality, it is necessary to conduct inspections and maintenance at appropriate intervals and exchange replacement parts when necessary. Improper inspections or maintenance may result in failure.
In addition, the warranty does not cover the use of the product in areas where salt damage can be expected or where there is a substantial presence of corrosive gases such as Cl2, H2S, SO2, and NO2. If the product is to be used in such areas, at the time of installation you must take appropriate steps to protect the product.
- (5)If the product is to be used with equipment/systems that must meet special quality and reliability standards (aerospace equipment, medical equipment, power generation control equipment, automotive/railway transportation equipment, safety equipment, disaster prevention and security equipment, etc.), please consult with our sales staff in advance.
- (6)Some products contain gallium arsenide (GaAs), classified as a harmful substance. To avoid danger, do not incinerate, crush, or chemically treat the product in such a way that gases or dust are released. When disposing of the product, comply with all applicable laws and regulations and do not treat it as general industrial waste or household waste.
- (7)When exporting a product or technology, observe export laws and regulations such as those governing foreign exchange and foreign trade, and obtain any necessary licenses for export, service transactions, etc.
We request that you do not use our products or the technical data published on this website for developing weapons of mass destruction or for any other military purposes or applications.
- (8)The product specifications on this website are subject to change without notice. If you are considering using a product, delivery specifications must first be settled.